89 "raspberry pi relay" You can choose the one that best suits your needs.This module is designed for switching two high powered devices from your Arduino.
Your recently viewed items and featured recommendations
Your recently viewed items and featured recommendations The second circuit is also switched off.When a small current flows through the first circuit, it activates the electromagnet, which generates a magnetic field all around it.The energized electromagnet attracts a contact in the second circuit toward it, closing the switch and allowing a much bigger current to flow through the second circuit.When the current stops flowing, the contact goes back up to its original position, switching the second circuit off again.Typically the relay has 5 pins, three of them are high voltage terminals (NC, COM, and NO) that connect to the device you want to control.The mains electricity enters the relay at the common (COM) terminal. We just need: Connect an Arduino's pin to the IN pin of the relay; Control the relay by programming the pin to LOW or HIGH Control Up to 65,280 Relays with Your Arduino! The shield provides two relays called RELAY1 and RELAY2 commanded by pin 1 and pin 2 respectively.The shield also provides an easy connection by means of screw terminal blocks to A1 to A4 analog inputs, I2C and supply voltages.. Operating voltage 3.3V (supplied from the host board) KEYESTUDIO 4 Channel Relay Shield 5V for Arduino Controller R3 ARM PIC AVR STM32 Raspberry Pi HIGH Level Trigger Relay Module Expansion Board 4.5 out of … Blinds (Or Any AC Power Motor) Control.
However there are other modules with one, four and eight channels. JBtek 4 Channel DC 5V Relay Module for Arduino Raspberry Pi DSP AVR PIC ARMHiLetgo 2pcs 5V One Channel Relay Module Relay Switch with OPTO Isolation High Low Level TriggerMCIGICM 2 Channel DC 5V Relay Module for Arduino UNO R3 DSP ARM PIC AVR STM32 Raspberry Pi with Optocoupler Low Level Trigger Expansion BoardYoungneer 5v Relay Board Relay Module 1 Channel Opto-Isolated High or Low Level TriggerKEYESTUDIO 4 Channel Relay Shield 5V for Arduino Controller R3 ARM PIC AVR STM32 Raspberry Pi HIGH Level Trigger Relay Module Expansion BoardSunFounder 2 Channel DC 5V Relay Module with Optocoupler Low Level Trigger Expansion Board for Arduino R3 MEGA 2560 1280 DSP ARM PIC AVR STM32 Raspberry PiJBtek 4 Channel DC 5V Relay Module for Arduino Raspberry Pi DSP AVR PIC ARMSunFounder 2 Channel DC 5V Relay Module with Optocoupler Low Level Trigger Expansion Board for Arduino R3 MEGA 2560 1280 DSP ARM PIC AVR STM32 Raspberry PiIot Relay - Enclosed High-power Power Relay for Arduino, Raspberry Pi, PIC or Wifi, Relay ShieldHuayao 2pcs 8 Channel DC 5V Relay Module with Optocoupler for Arduino UNO R3 MEGA 2560 1280 DSP ARM PIC AVR STM32 Raspberry PiKeeYees 5pcs 1 Channel 5V Relay Module Board Shield KY-019 LED Indicator for Arduino Raspberry Pi PIC AVR DSP ARM + 3pcs 20CM 10Pin Female Male Jumper WiresSunFounder Relay Module for Arduino and Raspberry Pi 5V DC Trigger by HIGHLO (HIGH Trigger)DAOKI 5 PCS 5v Relay Module for Arduino ARM PIC AVR MCU 5V Indicator Light LED 1 Channel Relay Module Works with Official Arduino BoardsQunqi 4pcs 5V 2 Channel 5V Relay Module with Optocoupler Low Level Trigger Expansion Board for Arduino UNO R3 MEGA 2560 1280 DSP ARM PIC AVR STM32 Raspberry PiELEGOO Mega 2560 Project The Most Complete Ultimate Starter Kit w/Tutorial Compatible with Arduino IDEFICBOX 6Pack 5V One 1 Channel Relay Module Board Shield with Optocoupler Support High and Low Level Trigger Power Supply Module for Arduino8 Channel DC 5V Relay Module with Optocoupler for Arduino UNO R3 MEGA AVR STM32 Raspberry PiJBtek 8 Channel DC 5V Relay Module for Arduino Raspberry Pi DSP AVR PIC ARMINSMA 433Mhz Wireless RF Switch Long Range DC 12V 4CH Channel Wireless Remote Control Switch, DC12V Relay Receiver Module, Transmitter Toggle Switch RF Relay (2 Transmitter & 1 Receiver) The channels are labeled for their function: common (COM), normally closed (NC), and normally open (NO)The names explain the state of the channel with relation to the switch at rest.On the other side of the module, there are four pins – a Ground pin and a VCC pin to power the module and two input pins IN1 and IN2 to control the relay.The input pins are active low, meaning the relay will be activated when you pull the pin LOW and it will become inactive when you pull the pin HIGH.Notice that the module has a jumper cap connecting the VCC and JD-VCC pins.The jumper cap allows you to choose whether the circuit is physically connected to the Arduino.When the jumper is in place, the electromagnet of the relay is directly powered from the Arduino. Huayao 2pcs 8 Channel DC 5V Relay Module with Optocoupler for Arduino UNO R3 M… $10.89 $ 10. The Arduino can be programmed to turn on the relay when a certain event occurs, for example when the temperature of a thermistor gets higher than 30°C. The StarterKit includes a book with 15 tutorials that will walk you through the basics up to complex projects. Prime members enjoy FREE Delivery and exclusive access to music, movies, TV shows, original audio series, and Kindle books. There is not much difference between the two modules, only the four channel relay module comes with two extra relays and two extra control pins.Let’s have a look at the pinout of two channel relay module.Now that we know everything about the relay module, it is time to put it to use!Start by connecting VCC pin on the module to 5V on the Arduino and GND pin to ground. You can use a relay module to control the AC mains and Arduino to control the relay.This tutorial walks you through how to setup the relay to switch on a lamp or other device, but let’s begin with a short introduction into relays.Here’s a simple animation illustrating how the relay uses one circuit to switch on another circuit.Initially the first circuit is switched off and no current flows through it until something (either a sensor or switch closing) turns it on. Sometimes you want your Arduino to control AC powered devices like lamps, fans or other household devices. Relay module for Arduino is one of the most powerful application for Arduino as it can be used to control both A.C and D.C devices by simply controlling the relay by giving 5V.