Skip to content
PETG hair . I have fine tuned from there for my setup but starting with the ABS profile + fan you should be close enough to get running.Another important thing is retraction must be set painfully slow or makes things worse.I can share my S3D PETG profile but it likely won't work as well for you since every printer is different.New comments cannot be posted and votes cannot be cast/r/3DPrinting is a place where makers of all skill levels and walks of life can learn about and discuss 3D printing.Press J to jump to the feed. Beim stöbern in meinem Profil-Ordner habe ich dazu eigentlich keine Abweichungen gefunden. Here, we’ll take you through how to successfully print with PETG and help you troubleshoot common issues. I'm not entirely sure how I managed to get it tweaked as well, but it's always worked nicely for me. At any rate, it's a modification of the profile that Josef Prusa originally provided. Discussion. Apr 30, 2019 . 1.
Press question mark to learn the rest of the keyboard shortcuts By using our Services or clicking I agree, you agree to our use of cookies. I do believe it's a little slower than some people might like, but I tried to tune it for strength and quality. Simplify3D … I have fine tuned from there for my setup but starting with the ABS profile + fan you should be close enough to get running.Another important thing is retraction must be set painfully slow or makes things worse.I can share my S3D PETG profile but it likely won't work as well for you since every printer is different.New comments cannot be posted and votes cannot be cast/r/3DPrinting is a place where makers of all skill levels and walks of life can learn about and discuss 3D printing.Press J to jump to the feed. But is there anyway place to get a PETG profile? Simplify3d PETG profile. It is very strong/durable, doenst warp, lift, or crack like ABS and isnt as brittle as PLA. After playing with it I really start to like it.
Drop a message and let us know how it goes? After playing with it I really start to like it. Want to 3D print with PETG on your beloved Ender 3 but aren't sure about the settings? The strength version doesn't use the part fan except for overhands.
The strength version doesn't use the part fan except for overhands. Here you go right here.
There are several ways to eliminate these print defects such as enabling “Extra Restart Distance” or “Coasting” options located in the Extruder tab. Currently I want to use PETG.
PETG, short for polyethylene terephthalate glycol, is a tough, temperature-resistant, and highly impact-resistant plastic often used in FDM-style 3D printing.There’s quite a lot to this material, so check out our full filament guide for more.. Can you choose other types - PLA, ABS, etc?I started out running with same profile as ABS but with cooling fan on right from the start. Recently i purchased some PETG, i wanted to print some spare parts for my Prusa i3 MK2S.I have a Prusa i3 MK2. At any rate, it's a modification of the profile that Josef Prusa originally provided. Simplify3D also includes an option to perform a dynamic retraction, where the filament is retracted while the extruder is still moving. naviathan - in reply to jeh241_makestuff . It is more sticky and oozy than PLA. News; Printables; Buyer's Guides; Reviews; Basics; Pro . What led you to use that?Negative restart distance means it will retract but then instead of pushing the filament out it will not push it as far out not sure about the details.
The results can be seen below. I haven't had any issues with stringing, and haven't had any real problems with oozing either. Though I do get the little blobs at the layer change, which is why I want to try the negative restart thing. 10 posts • Page 1 of 1. jheikkila54 Posts: 18 Joined: Wed Jun 24, 2015 12:44 pm. But is there anyway place to get a PETG profile?I don't remember if PETG came as one of the profiles or if I created it myself. The material also benefits from great thermal characteristics, allowing the plastic to cool efficiently with almost negligible warpage. Out of the material configurations, the ones to look at are the PETG and PETG-Strength. This completely eliminates blobs that are typically formed from a stationary retraction.
naviathan, I'll have to check that out too. News Printables Buyer's Guides Reviews Basics.
I adjust it some depending on what I'm printing, but you may want to tone that down to 30-50%. Jul 11, 2018 .
I've been tweaking my settings some, still.
As a quick note, on the regular PETG profile, the part fan is at 100%. Your settings are pretty much the same as mine. I've been doing well at 1mm without wiping. After turning off wiping I set it to 1mm as 0.8 just didn't seem to kill all the fuzzies.
I just bought a 3d printer and a friend of mine "gave" me simplify3d. 10 posts • Page 1 of 1. dorgeman Posts: 18 Joined: Fri Oct 30, 2015 10:13 pm. Original_Prusa_i3_MK2_RC4-Josheh.fff .
Here are my settings my i3 clone for 0.4 nozzle 0.2mm layer.
Starting with the "generic PETG" profile in Cura 4.0, with following modifications Layer Height: 0.15 Initial Layer Height: 0.3 Extruder temp: 245 Bed temp: 75 Print speed: 40 Initial layer speed: 20 Skirt/Brim speed: 20 Number of slower layers: 2 Fan speed: 100 Regular fan speed: 80 Initial fan speed: 0 Regular fan at layer: 3.
Attached is my simplify 3d profile that I've been using. Sun Apr 24, 2016 1:58 am . Wed Jul 01, 2015 6:24 pm . share. So, I thought maybe being able to take a look at my profile could be useful.
I personally think this is the best S3d profile I found for PLA if you're looking for one, got it from a member of the facebook group, the same person also did one for PETG so here's one for both since they don't require an enclosure and there's probably a lot of new people with christmas cr-10's looking for profiles.